Product sorting
List of products
This is the thinner version of C245908. Its 1 mm thickness at a 4.8 mm width accommodates thinner components. For JBC T245 handles.
The forked Chip end is intended for desoldering chip components. Match the 1.25 mm tip size to the component geometry. For JBC T245 handles.
The forked Chip end has a designated size of 2 mm. Check the component terminal shape and spacing when choosing it. For JBC T245 handles.
A width of 2.4 mm and thickness of 0.5 mm form a thin chisel in an HT design. For JBC T245 handles.
JBC C245760: barrel tip for cables Ø 3.5 mm. The concave end is shaped for soldering cable connections. For JBC tools T245.
This bent version of C245061 reaches joints that are difficult to access with the straight chisel. For JBC T245 handles.
JBC C245762: round connector tip R 4.5 mm. The rounded recess contacts cylindrical terminals when soldering cables and connectors. For JBC tools T245.
JBC C245763: barrel tip for cables Ø 2.5 mm. The concave end is shaped for soldering cable connections. For JBC tools T245.
JBC C245764: narrow conical tip Ø 0.5 mm. The conical end provides point contact with an individual solder joint. For JBC tools T245.
Compared with C245939, the less sharp bevel helps keep solder close to the edge. For JBC T245 handles.
The large bevelled contact surface is intended for soldering wide areas. The working-end diameter is 5 mm. For JBC T245 handles.
This tip combines a 1.5 mm width with a thin 0.3 mm end. Choose it according to the contact-edge width required. For JBC T245 handles.
This slender version of C245741 is 2.4 mm wide and 0.3 mm thick, providing a thin contact edge. For JBC T245 handles.
JBC C245771: narrow bent chisel tip 1 × 0.1 mm. The bent chisel combines a flat contact with angled access to the joint. For JBC tools T245.
JBC C245772: nickel chisel tip 1.4 × 0.7 mm. The flat end can contact a solder pad along its edge or across its broader face. For JBC tools T245.
This is the slender version of C245742: the width remains 0.8 mm, while the thickness is 0.3 mm. For JBC T245 handles.
This slender alternative to C245906 retains a 1.2 mm width with a reduced thickness of 0.3 mm. For JBC T245 handles.
The tip is 7 mm longer than C245911, improving access to difficult-to-reach joints. For JBC T245 handles.
JBC C245776: blade tip 37 mm. The broad blade provides contact along an extended soldering area. For JBC tools T245.
The 2.8 mm bevel has a reduced tinned surface for local touch-up work. For JBC T245 handles.
JBC C245785: barrel tip for cables Ø 1.5 mm. The concave end is shaped for soldering cable connections. For JBC tools T245.
The conical body ends in a short bent 0.4 mm tip. Compare the complete working profile when choosing this model. For JBC T245 handles.
The 3.8 × 0.3 mm knife edge combines an angled blade with a thin contact end. For JBC T245 handles.
JBC C245790: barrel tip for cables Ø 0.8 mm. The concave end is shaped for soldering cable connections. For JBC tools T245.
JBC C245791: Ø 9.8 mm. heat-staking tip for plastics. The tip transfers heat to plastic during heat staking. For JBC tools T245.
JBC C245792: blade tip 40 mm. The broad blade provides contact along an extended soldering area. For JBC tools T245.
This 2.8 mm bevel presents an angled tinned face to the solder joint. For JBC T245 handles.
The 30 mm tip length is intended for hard-to-reach solder joints. It ends in a 2.5 mm bevel. For JBC T245 handles.
JBC C245796: drag soldering tip 2.2 × 0.75 mm. The forked design is intended for drag soldering through-hole leads. For JBC tools T245.
The reduced tinned area on the 3.8 mm bevel is intended for solder touch-up work. For JBC T245 handles.
JBC C245798: heat-staking tip for plastics Ø 8 mm. The tip transfers heat to plastic during heat staking. For JBC tools T245.
The straight 4.5 mm blade creates a continuous flat contact edge for soldering work. For JBC T245 handles.
JBC C245803: conical tip Ø 1 mm. The conical end provides point contact with an individual solder joint. For JBC tools T245, ALE250.
JBC C245804: bent conical tip Ø 1 mm. The bent end provides angled access to the joint. For JBC tools T245.
JBC C245806: chisel tip 1.2 × 0.7 mm. The flat end can contact a solder pad along its edge or across its broader face. For JBC tools T245, ALE250.
JBC C245807: chisel tip 2.2 × 1 mm. The flat end can contact a solder pad along its edge or across its broader face. For JBC tools T245, ALE250.
JBC C245808: chisel tip 4.8 × 1.5 mm. The flat end can contact a solder pad along its edge or across its broader face. For JBC tools T245.
JBC C245811: chisel tip 3.2 × 1.2 mm. The flat end can contact a solder pad along its edge or across its broader face. For JBC tools T245.
JBC C245812: bevel tip Ø 3 mm. The bevel provides a contact face for soldering with the handle held at an angle. For JBC tools T245.
JBC C245844: chisel tip 1.8 × 0.8 mm. The flat end can contact a solder pad along its edge or across its broader face. For JBC tools T245.
JBC C245845: bevel tip Ø 2.2 mm. The bevel provides a contact face for soldering with the handle held at an angle. For JBC tools T245, ALE250.
JBC C245846: bent chisel tip 2.2 × 1 mm. The bent chisel combines a flat contact with angled access to the joint. For JBC tools T245.
JBC C245862: bent chisel tip 1.2 × 0.7 mm. The bent chisel combines a flat contact with angled access to the joint. For JBC tools T245.
JBC C245863: bent chisel tip 1.8 × 0.8 mm. The bent chisel combines a flat contact with angled access to the joint. For JBC tools T245.
JBC C245866: chisel tip 6.6 × 1.8 mm. The flat end can contact a solder pad along its edge or across its broader face. For JBC tools T245.
JBC C245875: chisel tip 3.2 × 1.2 mm. The flat end can contact a solder pad along its edge or across its broader face. For JBC tools T245.
The 1 mm conical end provides a standard straight geometry for general soldering. Match the diameter to the joint contact area. For JBC T245 handles.
This bent 1 mm model provides a conical contact end for reaching joints away from the tool axis. For JBC T245 handles.
The 1.5 mm bevel presents an angled face to the joint. This model carries no HT designation. For JBC T245 handles.
This straight 1.2 × 0.7 mm chisel is a general-purpose model for joints needing a flat contact edge of this size. For JBC T245 handles.
